Welcome!

22 Comments

1. booM
   Posted December 28, 2006 at 2:57 pm | Permalink

   Caya PIJUT… ko sememangnya pepijut alaf.. ahahahahhaah
   a very usefull site.. good for newbies like me…
   keep up the good work!!

   Reply
2. naz
   Posted January 22, 2007 at 11:38 pm | Permalink

   i’m a newbie here…
   i’m using HuaWei SmartAX MT800A..

   1. u said make sure to set VCI-0, VPI-35
   but mine is VCI-35, VPI-0
   so, do i need to change that ?

   2. when i change to PPPoE, there is a blank box for service name?
   what should i put there??

   i hope u can help me..

   Reply
3. pijut82
   Posted January 30, 2007 at 7:20 pm | Permalink

   *naz – ops i think it was a mistake there.. hehe.. the true VCI-35, VPI- 0
   thanks for remind me…
   just put streamyx for your service name..or any name that u want…

   * hehhe sorry 4 late reply since i was busy clearing the spam comment.
   TQ

   Reply
4. coltfirearms
   Posted February 5, 2007 at 1:29 am | Permalink

   thanks bro..site ni mmg best ar..

   Reply
5. 30I|I08
   Posted February 18, 2007 at 2:31 pm | Permalink

   Assalammualaikum bro,

   Kalau boleh, letak sekali manual guide untuk disable kan auto connection tak? Berguna tu sesekali kalau nak troubleshoot streamyx problem.

   Reply
6. tmnet
   Posted February 19, 2007 at 1:08 pm | Permalink

   Bro..kalo sumer customer Streamyx bukak website ko ni kan senang…x payahla aku yang keje Customer Service Streamyx pick up call lagi..haha…nanti aku rekemenkan Streamyx soh publishkan ko punya page nie..kalo ko nak troubleshooting sume pasal apa2 problem streamyx pon aku boleh bagi…ade la sedikit sebanyak aku bleh tolong…ok..

   Reply
7. pijut82
   Posted February 20, 2007 at 1:27 pm | Permalink

   *tmnet – hmm i think it should help me a bit.. ahaha.. just email to me all troubleshooting that probably u have in mind and from there i will edit it before post it here, email it to me…
   thank you

   Reply
8. StreamyxTech
   Posted April 17, 2007 at 2:20 pm | Permalink

   yo bro.. site ni mmg best..
   pasni ni aku rekemen site ni kat cust.. huhu..

   Reply
9. Zaim(StrmyxTech)
   Posted April 17, 2007 at 2:27 pm | Permalink

   -Site ni bagus tok customer yg kureng IT knowledge.
   huhu..
   -harap2 semua cust refer to page ni b4 call techsup.
   -trus kan useha yg murni ni. haha..

   Reply
10. inginTAHU
    Posted May 16, 2007 at 1:08 am | Permalink

    tumpang tanye.. camne nk tau nombor port?? ye r, kalo time “port forwarding” tu..

    Riger DB102

    Reply
11. pijut82
    Posted May 16, 2007 at 1:39 pm | Permalink

    you can go to this website for reference
    http://portforward.com

    Reply
12. zlan07
    Posted September 1, 2007 at 1:23 pm | Permalink

    tanya skit…mcm mana nak buat portforward..aku guna caremo as520..aku dah ikut step dlm website portforward.com..spai kat dia suruh pilih modem yg aku guna..modem aku xda dlm list..tolong ye

    Reply
13. pijut82
    Posted September 3, 2007 at 7:30 pm | Permalink

    - zlan07-
    the important part is you just need to know what port you need to configure and base on what i assume your using the PFConfig that been supplied by Port Forward itself.

    when you know which port you likely will use just add it inside the NAT rules and the protocol should be TCP / UDP.

    Reply
14. emmi
    Posted November 12, 2008 at 11:00 pm | Permalink

    The first modem yg i ingat… CellPipe – Lucent, kena configure pakai serial port tuh…

    sekarang ni cocos je auto play

    Reply
15. Jibet
    Posted January 1, 2009 at 11:28 pm | Permalink

    pijut..tmpg tnyer..
    aku nk tau cmner nk buat DSL light x blinking? cam solid?

    Reply
16. sham
    Posted April 16, 2010 at 2:54 pm | Permalink

    aku guna modem riger db108-wl nak setting auto connection,,,,ops aku masukkan ip address modem 192.168.1.1 but then tak kuor website die….camana ni bro??tolong..

    Reply
    • pijut82
      Posted April 19, 2010 at 2:16 pm | Permalink

      try to check your own ip.. is it in the group of 192.168.x.x ?

17. sham
    Posted April 21, 2010 at 8:45 pm | Permalink

    aku taip ipconfig,,,,mmg gruop 192.168.xxx.xxx

    Reply
    • pijut82
      Posted April 21, 2010 at 9:46 pm | Permalink

      okies..
      when you do the ipconfig/all, do you see your default gateway (modem) ip?

18. sham
    Posted April 24, 2010 at 2:51 am | Permalink

    tak ader pon

    Reply
19. fadli
    Posted June 3, 2010 at 12:22 pm | Permalink

    salam…..
    nak tanya beberapa soalan…
    mcm mana nak connect wireless router ke adsl modem?
    wireless router Aztech WL730RT4
    adsl modem D-link 520B
    nak configure mcm mane yerk?
    kalau guna modem sahaja,internet connection ok
    kalau guna wireless + modem,internet connection gagal…

    mcm mana nak configure signal dari wifi ke adsl?
    kalau boleh balas melalui email yerk…
    terima kasihhh…bro

    Reply
    • pijut82
      Posted June 6, 2010 at 10:01 pm | Permalink

      refer to my new post..
      thanks